P870km /km1 coffelake support bios are on line now

Discussion in 'Sager and Clevo' started by 52571abc, Jul 6, 2018.

Tags:
  1. Dr. AMK

    Dr. AMK Living with Hope

    Reputations:
    2,832
    Messages:
    1,871
    Likes Received:
    3,955
    Trophy Points:
    281
    I already did that before start using it. anything more than 4.80ghz will get so hot.
    I'm happy with the huge performance improvement for the 8086K @4.70Ghz 6 cores than my 7700k, at this speed with some undervolting the heat will be within acceptable range.

    I need to test the Stock TM1 BIOS as well, as advised by respectable member.
     
  2. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,146
    Messages:
    51,630
    Likes Received:
    14,723
    Trophy Points:
    931
    Past that it does get sample specific, mine runs about -125mv at 5ghz with the tm cooler.
     
    Dr. AMK likes this.
  3. Dr. AMK

    Dr. AMK Living with Hope

    Reputations:
    2,832
    Messages:
    1,871
    Likes Received:
    3,955
    Trophy Points:
    281
    I think mine can run the same if I can change the cooler, so the question is: can I replace the KM1 cooler with the TM1 cooler? is it needs any mods?

    Now I'm running at 4.80Ghs 1190v/-125, I succeed to render and gaming and the temps 81c max after 1 hour BF1.

    The BIOS I'm using now is the Stock TM1 BIOS, all cores appears correctly, and no issues so far, except the G.Sync is not available. I don't use it anyway. Until I can find a good BIOS mod that I can depend on.
     
  4. Papusan

    Papusan JOKEBOOK's Sucks! Dont waste your $$$ on FILTHY

    Reputations:
    22,505
    Messages:
    23,535
    Likes Received:
    40,813
    Trophy Points:
    931
    You need the TM models Cpu backplate. Because the screw mounting piece is shorter on P870Tm models. Fully disassembly. + cut the pipes from the Gpu grid going to Cpu grill.
     
    Dr. AMK likes this.
  5. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,146
    Messages:
    51,630
    Likes Received:
    14,723
    Trophy Points:
    931
    The overall fit on height is a bit different so yes you need that back plate too.
     
    Dr. AMK likes this.
  6. Dr. AMK

    Dr. AMK Living with Hope

    Reputations:
    2,832
    Messages:
    1,871
    Likes Received:
    3,955
    Trophy Points:
    281
    Tell me what to do and what/where to buy and I'll just follow your instructions.
     
  7. Papusan

    Papusan JOKEBOOK's Sucks! Dont waste your $$$ on FILTHY

    Reputations:
    22,505
    Messages:
    23,535
    Likes Received:
    40,813
    Trophy Points:
    931
    I don’t have it. + DM has 5v fans. Not much to buy here home. @bloodhawk have done the mod.

    Edid. And I mean @Prema put in a TM Mb.
     
    Dr. AMK likes this.
  8. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,146
    Messages:
    51,630
    Likes Received:
    14,723
    Trophy Points:
    931
    Reach out to a local reseller might be your best bet.
     
    Dr. AMK likes this.
  9. Dr. AMK

    Dr. AMK Living with Hope

    Reputations:
    2,832
    Messages:
    1,871
    Likes Received:
    3,955
    Trophy Points:
    281
    I'll try to contact him.

    I have a conversation with him today, and I'll ask him about that,

    We don't have any local resellers in the whole ME/Gulf region. Anything I need must be ordered from US, Europe or Chaina.
     
  10. Dr. AMK

    Dr. AMK Living with Hope

    Reputations:
    2,832
    Messages:
    1,871
    Likes Received:
    3,955
    Trophy Points:
    281
    Can I have your Throttlestop and BIOS settings?
     
Loading...

Share This Page