*** Official Clevo Sager NP9155 / P750TM-G / P751TM-G Owner's Lounge! ***

Discussion in 'Sager/Clevo Reviews & Owners' Lounges' started by Spartan, Oct 6, 2017.

  1. jc_denton

    jc_denton V̖̟en̰g̻̼̰̩͙ea̲n̪c̭e̼ ͍̘̤͓̟̤Is̙͔ ̤Mi̻̭̣͎͍ͅn̰ḙ

    Reputations:
    2,912
    Messages:
    1,568
    Likes Received:
    2,088
    Trophy Points:
    181
    They really should include thermal pads spec used in the manual or something, would make it a lot easier to buy replacements yourself. Instead of hopping through hoops.
     
  2. jaybee83

    jaybee83 Biotech-Doc

    Reputations:
    4,095
    Messages:
    11,564
    Likes Received:
    9,125
    Trophy Points:
    931
  3. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    Hey guys I noticed that If I run on just battery, I can actually game at High FPS. This P750TM1-G does not cap to 30 FPS. I’ve managed about 1.5 hours of gaming on just the battery alone. And I’m getting High FPS around 60+

    My last Aorus X7 V7 would instantly lock 30FPS
     
  4. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,568
    Messages:
    53,441
    Likes Received:
    15,384
    Trophy Points:
    931
    There are different performance limit modes in the nvidia panel.
     
  5. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    I know but I could never get more than 30fps out of my last laptop regardless of performance settings.
     
  6. yrekabakery

    yrekabakery Notebook Virtuoso

    Reputations:
    890
    Messages:
    2,652
    Likes Received:
    2,515
    Trophy Points:
    181
    That sounds like Battery Boost (an FPS limiter inside GeForce Experience).
     
  7. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    I would recommend this to anyone with one of these laptops. They’re flathead, pan head, stainless steel screws for the GPU.

    I was reaching 83C after paperclip mod at 1,898Mhz with 0.925V. With the factory Phillips screws that strip very easily. I was limited on tightening pressure that I could apply.


    I could finally tighten firm with the flat heads so I could really squeeze down these gelid pads and get them puppies snug!

    Now I’m down to 77C at 1,898Mhz 0.925V.

    If I drop my memory overclock to +0 temps are around 71C. Memory overclock increases temps drastically.

    I know my laptop, and I could see a difference immediately.


    [​IMG]
     
    Last edited: Dec 25, 2019
  8. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,568
    Messages:
    53,441
    Likes Received:
    15,384
    Trophy Points:
    931
    What size did you get?
     
  9. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    2x4mm. I ordered #100 of them. The bottom panel screws fit cpu retention bracket holes, and they do not strip as easily so the stock screws are fine.
     
    FTW_260 likes this.
  10. FTW_260

    FTW_260 Notebook Consultant

    Reputations:
    70
    Messages:
    218
    Likes Received:
    130
    Trophy Points:
    56
    I can’t find exactly such screws, could you share the link? ;)
     
Loading...

Share This Page