*** Official Clevo P75xDM and P77xDM/Sager NP9758-G and NP9778-G "Batman 2.0" Owner's Lounge ***

Discussion in 'Sager/Clevo Reviews & Owners' Lounges' started by ProFX, May 18, 2015.

  1. p3duy

    p3duy Notebook Enthusiast

    Reputations:
    0
    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    5
    My card 1 is empty, today i sodered 1,2,3. Tomorrow i'll try 4,5.

    Thanks so much.
     
  2. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,878
    Messages:
    55,291
    Likes Received:
    16,160
    Trophy Points:
    931
    Must have steady hands, those things are tiny.
     
  3. IllusiveMan

    IllusiveMan Notebook Consultant

    Reputations:
    42
    Messages:
    296
    Likes Received:
    85
    Trophy Points:
    41
    There is no resistor in place you marked with 1. Checked the green PCB card, it's nothing there.
     
  4. Patrick McNamara

    Patrick McNamara Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    I was hoping I could get some help with my P750DM.

    So my Original screen stopped working which is the Chimei N156HGE-LA1, which has LVDS interface. Looking at the eurocom screen upgrade page located here

    https://eurocom.com/ec/lcd()upgrade

    I was under the impression that I could upgrade to the Sharp LQ156D1JW04 4k screen, so I purchased one with correct wire needed to upgrade as well. Now I knew this was an eDP interface but I thought that my board had both LVDS and eDP. Upon opening the computer and inspecting the board it does look like it has both but the connector for the eDP interface is not soldered to the board. I have a picture if that would help just let me know.

    My question is what are my options from here? Can I solder a connector to the eDP part of the motherboard? Move the connector from LVDS to eDP? Is there any other way to get an eDP screen working with the LVDS version of the P750DM? I'd really like to find a way to use the Sharp screen if possible.
    If I purchased a new board with the connector soldered properly could I swap over all parts? Should I just get a new LVDS screen? If so are there any better options than the Chimei?


    I'd appreciate any help you'd have to offer. Thanks in advance.
     
  5. biom4t

    biom4t Newbie

    Reputations:
    0
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    5
    Hello.

    I have a P751DM-G with a NVIDIA GTX 970m, however the driver I have installed has been released in 2015 and I can't update it.
    Whether I download new drivers from NVIDIA website, from Windows Update or even from the PC manifacturer website the video card disconnects and it gives me the following error:
    Code 43 (Windows has stopped this device because it has reported problems)
    To reconnect the video card I have to reinstall the old drivers 10.18.13.5900.

    Anyone knows what can I do?
    Thank you in advance.
     
  6. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,878
    Messages:
    55,291
    Likes Received:
    16,160
    Trophy Points:
    931
    Have you tried a fresh install of Windows?
     
  7. biom4t

    biom4t Newbie

    Reputations:
    0
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    5
    No I haven’t.

    Do you think it’s impossible to update the driver without losing my files?
     
  8. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,878
    Messages:
    55,291
    Likes Received:
    16,160
    Trophy Points:
    931
    Take an image backup and see if it helps. You should also backup your files.
     
Loading...

Share This Page