*OFFICIAL* Alienware Area-51M Owner's Lounge

Discussion in '2015+ Alienware 13 / 15 / 17' started by ssj92, Jan 8, 2019.

  1. S.K

    S.K Batch 80286

    Reputations:
    334
    Messages:
    912
    Likes Received:
    1,045
    Trophy Points:
    156
    You could also take a look at other stuff and replace things as necessary. This is good!

    As far as your question about limits, that is expected with link degradation. X2 can only handle this much.
     
    Last edited: Jun 22, 2019
    Nomadsan74 likes this.
  2. Nomadsan74

    Nomadsan74 Notebook Consultant

    Reputations:
    113
    Messages:
    157
    Likes Received:
    295
    Trophy Points:
    76
    Ok here iFixit kit ready... here we go again screwdriver...

    [​IMG]

    Wish me good luck..

    I'll take some photos of my dead gc unit to compare to the healthy one
     
    S.K, Vasudev, hmscott and 1 other person like this.
  3. VoodooChild

    VoodooChild Notebook Evangelist

    Reputations:
    517
    Messages:
    539
    Likes Received:
    1,006
    Trophy Points:
    156
    Good luck!

    Sent from a Galaxy S9+
     
    Nomadsan74 likes this.
  4. Nomadsan74

    Nomadsan74 Notebook Consultant

    Reputations:
    113
    Messages:
    157
    Likes Received:
    295
    Trophy Points:
    76
    Ok i'm in the middle of the process...

    I've noticed that my old gpu of the unit that died WASN'T equiped with the mosfet heatsink !!!!!

    [​IMG]

    Is this normal ???? Maybe that's why my old unit died....

    Anyway... I attached the old cable on the new laptop clean the gpu with Isopropanol 99.9% and I'll be continuing after as small break... I need to eat and rest before continuing...

    Some photos of the fixed setup (I've checked... my GPU is equiped with 303150 Mosfets ;) :

    [​IMG] [​IMG] [​IMG] [​IMG] [​IMG]
     
  5. doofus99

    doofus99 Notebook Deity

    Reputations:
    233
    Messages:
    923
    Likes Received:
    478
    Trophy Points:
    76
    Not superstitious or anything but you're on page '13' '13' :)
     
    S.K, raz8020, Vasudev and 1 other person like this.
  6. hmscott

    hmscott Notebook Nobel Laureate

    Reputations:
    6,407
    Messages:
    19,717
    Likes Received:
    24,513
    Trophy Points:
    931
    Actually, Page 1313 for me is Page 1:

    My Preferences for "VB 3.1 - Fluid":

    "Thread Display Mode" : "Newest Post First".

    As always, it is a matter of perspective. :)
     
    Last edited: Jun 22, 2019
    raz8020, Vasudev, etern4l and 2 others like this.
  7. SacraficeMyGoat

    SacraficeMyGoat Notebook Evangelist

    Reputations:
    50
    Messages:
    537
    Likes Received:
    342
    Trophy Points:
    76
    2070 or 2080?
     
  8. Nomadsan74

    Nomadsan74 Notebook Consultant

    Reputations:
    113
    Messages:
    157
    Likes Received:
    295
    Trophy Points:
    76
    It's a 2080..

    Ok guys... that was hard but it seems that I fixed it !


    First try I put the thermal paste... put everything back in place.....

    I obtained a PCIe x4... damn !! Still not good...

    I unmounted everything.... went to the unmounting of the GC step.... decided to swap one of the GC cable... put the heatsink back... only plug power supply usb and displayport... run supportassist....

    Test: passed !....

    Finally !!...

    Now I need to put everything back.... see ya in a hour...
     
    Vasudev and c69k like this.
  9. Kernelghost

    Kernelghost Newbie

    Reputations:
    0
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    5
    Hi All,

    Looking for some advice....

    Got my unit only a month ago. After 7 days of use the whole unit failed.

    Dell tech replaced the motherboard and GPU - retained the CPU. I observed he had to remove the heatsink from the existing GPU when replacing the GPU as they hadn't send a card with heatsink attached or included.

    I'm not certain if before the replacement parts the situation was any better as I'd hardly had a chance to put the unit through it's paces due to working so much, however here's the situation:

    - When connected via display port to my acer predator X34A (100Hz - 3440x1440) I experience the most insane frame rate drops - I'm talking down to 5 fps at the worst. I've given up trying to play games on this monitor with the 51m. Even adjusting resolution down the issue remains.
    - Connected to this monitor running Valley or Superposition benchmark, the results are incredibly erratic, and I definitely see the abovementioned low frames all the way down to 5fps. I also observer the clock speed dips to 300-450Mhz.
    - Using the inbuilt display, 1920 x 1080 framerates are rock solid - even on extreme/ultra settings its a stable 50+ FPS.

    I'm on the latest 1.5.4 firmware also...

    I have an Alienware 17 R4 with the gtx 1070 and I've never had an issue using this display.

    I've been so annoyed I gave up trying to game on this at all.

    Any suggestions you can offer would be appreciated.
     
  10. Spkilla

    Spkilla Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    @VoodooChild
    Oh god..., mine comes from them this week, hoepfully mine comes in a better condition or ima try to return and just go to the clevo 870 or gt76 sigh...as much as i love this devices aesthetics over the other 2
     
Loading...

Share This Page