New toy!!

Discussion in 'Panasonic' started by mattpayne, Feb 26, 2010.

Thread Status:
Not open for further replies.
  1. uczmeg

    uczmeg Newbie

    Reputations:
    0
    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    5
    Just picked up one of these for a project and the lack of USB cable is annoying!

    For those of us who don't DIY has anyone sourced the cable (preferably UK based)?

    When I hard reset the system it goes through an install of software that just seems to remove a lot of Windows Mobile functionality, if (as I've done on other devices) I quit before this install happens I get the proper Windows Mobile, but I also get a warning dialog telling me to hard reset to do the full install.

    It's impossible to lose this dialog as it seems to survive being killed in the running programs!

    Any suggestions how to get full WM without the dialog?

    Thank you.
     
  2. onirakkiss

    onirakkiss Notebook Deity

    Reputations:
    552
    Messages:
    711
    Likes Received:
    23
    Trophy Points:
    41
  3. uczmeg

    uczmeg Newbie

    Reputations:
    0
    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    5
    Okay, went through all the thread again and found this post from Hanny and managed to answer my second question:

    This worked a treat. Thank you.
     
  4. uczmeg

    uczmeg Newbie

    Reputations:
    0
    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    5
  5. uczmeg

    uczmeg Newbie

    Reputations:
    0
    Messages:
    8
    Likes Received:
    0
    Trophy Points:
    5
    Could someone make me a few of these USB cables?

    Happy to pay for the parts, your time and postage....
     
  6. onirakkiss

    onirakkiss Notebook Deity

    Reputations:
    552
    Messages:
    711
    Likes Received:
    23
    Trophy Points:
    41
    I found some nice options for the cf-p2 in the schematic diagram (GPS,CIF-camera,wlan), which I will try in the next days. :)
     
  7. maninblack_30

    maninblack_30 Notebook Guru

    Reputations:
    0
    Messages:
    65
    Likes Received:
    0
    Trophy Points:
    15
    VERY interested, keep us posted!:D
     
  8. bigbadbob

    bigbadbob Notebook Enthusiast

    Reputations:
    0
    Messages:
    41
    Likes Received:
    0
    Trophy Points:
    15
    Schematic diagram????? please please can i have a copy?
     
  9. bigbadbob

    bigbadbob Notebook Enthusiast

    Reputations:
    0
    Messages:
    41
    Likes Received:
    0
    Trophy Points:
    15
    Thanks to Onirakkiss. good karma to the man.
     
  10. bigbadbob

    bigbadbob Notebook Enthusiast

    Reputations:
    0
    Messages:
    41
    Likes Received:
    0
    Trophy Points:
    15
    here's the full pinout for the 14 pin connector. (from onirakkis)

    1=gnd
    2=usb host D+
    3=usb host D-
    4=usb sync D+
    5=usb sync D-
    6=usb +5v in (usb detect)
    7=i2c bus clock (this bus seems to output system data to somewhere???)
    8=i2c bus data
    9=audio out to car speaker
    10=gnd
    11=audio in from car mic
    12=cradle detect (input,active low)
    13=external power/charge
    14= cradle int??? (input,active low)

    pda does not supply +5v for usb device, this must be externally supplied.
    there should be a radio mute signal somewhere too.
     
Thread Status:
Not open for further replies.

Share This Page