Mobile Pascal TDP Tweaker Update and Feedback Thread

Discussion in 'Sager and Clevo' started by Coolane, Jun 20, 2017.

  1. Vyor

    Vyor Notebook Enthusiast

    Reputations:
    5
    Messages:
    18
    Likes Received:
    8
    Trophy Points:
    6
    Any chance of getting this to work with the 1050M?
     
  2. Coolane

    Coolane Notebook Consultant

    Reputations:
    269
    Messages:
    224
    Likes Received:
    520
    Trophy Points:
    106
    Yes. But I haven't been able to find a mobile 1050/1050ti vBIOS online. If you happen to have one, do you think you can share it with me over the cloud?
    Otherwise I will see if I can extract it from some system BIOS package.
     
    Falkentyne likes this.
  3. Vyor

    Vyor Notebook Enthusiast

    Reputations:
    5
    Messages:
    18
    Likes Received:
    8
    Trophy Points:
    6
    Sure, I'll just grab the bios from this laptop.... once I figure out why NVFlash isn't seeing the 1050.
     
  4. thegh0sts

    thegh0sts Notebook Prophet

    Reputations:
    850
    Messages:
    6,957
    Likes Received:
    2,367
    Trophy Points:
    331
    most likely the version you are using doesn't support it. maybe there's a newer version.
     
  5. leeloyd

    leeloyd Notebook Consultant

    Reputations:
    57
    Messages:
    226
    Likes Received:
    148
    Trophy Points:
    56
    Optimus maybe ?

    @Vyor Can you switch to Discreete GPU only mode before dumping with NVFlash ?
     
  6. thegh0sts

    thegh0sts Notebook Prophet

    Reputations:
    850
    Messages:
    6,957
    Likes Received:
    2,367
    Trophy Points:
    331
    or just find the vbios chip and flash directly.
     
  7. Vyor

    Vyor Notebook Enthusiast

    Reputations:
    5
    Messages:
    18
    Likes Received:
    8
    Trophy Points:
    6
    It sees it as a PCI-E device, just doesn't recognize it as a NVIDIA chip.

    I lack the tools to do so at the moment. That and as far as I can see the chip is underneath a heat sink and I lack thermal paste.
     
  8. Mobius 1

    Mobius 1 what is quality control?

    Reputations:
    2,702
    Messages:
    7,713
    Likes Received:
    4,869
    Trophy Points:
    431

    Try nvflash with safe mode to flash/extract
     
  9. tanzmeister

    tanzmeister Notebook Evangelist

    Reputations:
    114
    Messages:
    526
    Likes Received:
    443
    Trophy Points:
    76
    I can get you a Ti vbios tomorrow.

    but any chance to make a volt editor? would be so nice to just be able to slide the voltage curve up or down without effecting the clocks
     
    Coolane and FTW_260 like this.
  10. tanzmeister

    tanzmeister Notebook Evangelist

    Reputations:
    114
    Messages:
    526
    Likes Received:
    443
    Trophy Points:
    76

    what I have found, that if you downvolt it with a Afterburner curve, you need to set the next lower clock before your actuall workload stable clocks to as little lower voltage offset possible compared to your workload stable clock.

    otherwise you loose performance, as you have mentioned.

    exactly as you have mentioned "sharp rising curve" is the issue here for some reason.
     
    Coolane and hmscott like this.
Loading...

Share This Page