[HowTo] SO-DIMMs Extreme: Boost 1600 to 2133 and beyond / JEDEC & XMP

Discussion in 'Hardware Components and Aftermarket Upgrades' started by James D, Jan 4, 2012.

Thread Status:
Not open for further replies.
  1. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    9,358
    Messages:
    6,297
    Likes Received:
    16,458
    Trophy Points:
    681
    533@CL9-9-9
    533@CL10-9-9

    GOOD LUCK ;)
     

    Attached Files:

  2. dadik

    dadik Notebook Enthusiast

    Reputations:
    0
    Messages:
    37
    Likes Received:
    0
    Trophy Points:
    15
    Aww hello m8 :)

    with both profiles i boot up as 8 7 7 7 20 :D single "A-DATA" wont boot :D so there has to be bios limitations, since this bios is like for 200types of DV6 notebooks and really few have DDR3 and correct me if I am wrong but DDR 2 had max CL8 right? There were some warnings to not try go for 9+ with DDR 2 maybe thats the problem. so far default A-data is best what i could achieve, with full 8 8 8 8 20 <== dunno why but tRAS remains still 20, even if it was following A-data spd table)


    btw I even reseted CMOS
     
  3. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    9,358
    Messages:
    6,297
    Likes Received:
    16,458
    Trophy Points:
    681
    Even within a CL range we can loosen the timings.
    So here Adata at the slowest CL8 (15ns...14.844ns is already CL9).
     

    Attached Files:

  4. dadik

    dadik Notebook Enthusiast

    Reputations:
    0
    Messages:
    37
    Likes Received:
    0
    Trophy Points:
    15
    Thanks, but bricked :D

    by the way there are 2 states of bricking in my case, one laptop simply wont POST and second capslock and numlock blinking with no POST, James D profiles and this one make caps+numlock blinking and those CL9 posted earlier doing the other type of not POSTING I am soo confused :D I simply give up, this is madness ! I hope that 8gig A-data will surprise me :D

    hello there,

    so :D A-data stick is useless, gotta give it back, intel PM45 can handle up to 8 gigs but obviously not single stick :)

    so Guys any tips for 4gig module which can handle 1333mhz with 1066 timings ? :)
     
  5. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    9,355
    Messages:
    57,927
    Likes Received:
    17,632
    Trophy Points:
    931
    You can get CL7 kingston hyper-X.

    EDIT: That may only be 2GB, Hmz, the 1600mhz modules can do that too.
     
  6. dadik

    dadik Notebook Enthusiast

    Reputations:
    0
    Messages:
    37
    Likes Received:
    0
    Trophy Points:
    15
    I ve had 2x4 GB kinston hyperX 1600 XMP ... worse modules then my samsung 1333 and micron 1333, so nope, definitely not kingston :) how about crucial modules ?
     
  7. James D

    James D Notebook Prophet

    Reputations:
    2,314
    Messages:
    4,901
    Likes Received:
    1,132
    Trophy Points:
    231
    Dadik, we already told you that most likely it is not RAM problem. Most likely CL8 is the highest your laptop can support.
     
  8. dadik

    dadik Notebook Enthusiast

    Reputations:
    0
    Messages:
    37
    Likes Received:
    0
    Trophy Points:
    15
    yes, thats why I am asking for best 4GB module which can be OCEd to run at 1333 with 1066 timings :)
     
  9. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    9,355
    Messages:
    57,927
    Likes Received:
    17,632
    Trophy Points:
    931
    I've run both my sets of kingston (1066 and 1600) at 1333mhz CL7, so I don't understand what you are asking?

    1333mhz at CL5? That's not going to happen.
     
  10. Shonk

    Shonk Notebook Enthusiast

    Reputations:
    31
    Messages:
    10
    Likes Received:
    0
    Trophy Points:
    5
    For people with a 1333 max cpu and Corsair CMSX4GX3M1A1600C9

    Who want 1333 CL7 with no extra profiles

    I edited the SPD data so it runs at the DDR3-1333F 7-7-7-20 Speed Bin

    [​IMG]

    http://www.mediafire.com/?jcfdn24h0j4a8hv

    Oh its also in bin format so it will flash with SPDTool and Thaiphoon Burner

    Just a quick update
    I made the spd data when the ram was still on order

    It has since come and been fitted and flashed
    I ran two passes of memtest last night at 1333 7-7-7-20 cr1 with 8gb
    and it passed with my sticks will run six pass at some point to be 100%
    but im still setting the laptop up with a fresh install of Win7
     
Thread Status:
Not open for further replies.

Share This Page