1. You may have noticed things look a little different around here - we've switched to a new platform (XenForo) and have some new forum styles and features. This how-to guide will help you find your way around. If you find anything that looks strange, post it in this thread.

Guide to Cooling Down Your Notebook Computer

Discussion in 'Notebook Dummy Guide Articles' started by Charles P. Jefferies, Jun 22, 2006.

  1. Charles P. Jefferies

    Charles P. Jefferies TG Lead Moderator Super Moderator

    Reputations:
    13,736
    Messages:
    34,722
    Likes Received:
    464
    Trophy Points:
    501

    by Charles Jefferies

    Does your notebook run hot or overheat? If it does, you are not alone. This guide is designed to help you reduce the temperature of your notebook considerably, all for little or no money and a few tweaks.

    <FONT color=red>Disclaimer: I take no responsibility for any damages caused if you use this guide.&nbsp; Be careful and all will be fine, but do proceed at your own risk!</FONT>

    Step 1: Fan Cleaning

    Cost: $0-$7

    Time: 10 to 15 Minutes

    Difficulty: Easy

    Applies to: Everyone

    <IMG height=202 src="http://www.notebookreview.com/assets/13349.jpg" width=198 border=0>

    Maintaining your notebook is important. The occasional wipe down is good, but that doesn't take care of the inside. Dust accumulates inside the notebook's cooling system after a while. It prevents air from flowing freely and traps heat.

    In order to get the dust out, you need a few supplies. The best way to get the heat out is with some canned compressed air, but that will cost you about $5 - $7 per can, depending on the store. It is well worth the money in my opinion. It can also be used to blow out the keyboard and other places in and on your notebook, such as ports. A cheaper but less effective way of getting dust out is by using a cotton swab and a handheld vacuum cleaner. I will show you how to do both.

    Before you start, turn off the notebook completely, unplug it from the wall, and take out the battery. Push down the power button a few times to drain any electricity running around.

    You must open up your notebook to access the fan(s). Turn the notebook upside down, and look for the compartment(s) where the fan(s) are. I suggest placing a towel under your notebook so the top doesn't get scratched. Unscrew all the screws holding down the compartment and carefully remove it. Place it and the screws in a safe place where they won't roll away.

    <IMG height=258 src="http://www.notebookreview.com/assets/13328.jpg" width=380 border=0><BR>CPU Fan vent (<A target=_blank href="http://www.notebookreview.com/assets/13327.jpg" >view large image</A>)

    With the internals of your notebook exposed, don't touch any of them -- oil from your hands is not good to get on the components, and you want to minimize the risk of damaging anything.

    <IMG height=270 src="http://www.notebookreview.com/assets/13330.jpg" width=360 border=0><BR>The internal components exposed. (<A target=_blank href="http://www.notebookreview.com/assets/13329.jpg" >view large image</A>)

    Using canned air:

    Open the package, read the directions on how to use the canned air -- it is very straightforward -- point and shoot. Before you start blasting the air into your notebook, squirt it a couple of times to get any moisture out of the nozzle. Once nothing but air comes out of the can, then you are ready to start. Hold the nozzle about 1-2 inches away from the fans and other dust-coated components and use quick bursts to blow any crud off. Be sure to blow out the fan and heat vents too, not just the physical fan. That's all you need to do. Some packages of canned air come with a plastic tube which you can insert into the nozzle. It helps concentrate the airflow. I recommend using this if your package has it -- you can get hard to reach places easier and it is more effective.

    Using cotton swabs:

    Take the cotton swabs and brush off all the fan blades and anything else that has dust on it. Once the swab is coated in dust, flick it with your fingers to clear the dust off of it. Don't use the same swab the whole time, get a new one after a couple of uses.

    When you are finished, get the handheld vacuum cleaner and suck up all the dust. Don't touch the notebook with the vacuum. Use your lung power to blow out the dust and help the vacuum cleaner as well. Repeat the steps above if there is still dust you missed in there. Get out as much as you can.

    Number Two: Cooling Pad

    Cost: $15-$30

    Time: 1-2 minutes

    Difficulty: Easy

    Applies to: Everyone

    A cooling pad is the best possible investment you can make for cooling down your computer. They increase the airflow under the computer, and greatly help the cooling system.

    There are many different coolers on the market. I will be reviewing two here:

    • <A target=_blank href="http://www.notebookreview.com/price/default.asp?cnetProductID=30631106" >Targus Chillmat</A> ($30, cheaper online)<BR><script src="http://www.NotebookReview.com/assets/19257bargainspots.js"></script><BR>
    • Spire Pacific Breeze (<A target=_blank href="http://www.newegg.com/Product/Product.asp?Item=N82E16834996501" >$15, Newegg.com</A>)

    Testing:

    I tested each cooler with my notebook's CPU undervolted and no Arctic Silver coolant applied (more on that later). The load temperature was measured while running 3DMark05. The room temperature was about 66 F during these tests.

    To see how well each cooler worked, I measured my standard temperatures while the notebook sat on a marble countertop. Standard temperatures:

    Idle: 46 Celsius CPU, 49 Celsius HDD

    Under Load: 57 Celsius CPU, 52 Celsius HDD

    <U>Targus Chillmat</U>

    <U></U>

    This is a simple, no-frills cooler with a basic design and quiet operation. It is lightweight, easy to transport, and draws its power from a USB port. I purchased my Chillmat from Best Buy for $29.99 -- it can be had for cheaper online, just shop around.

    <IMG height=214 src="http://www.notebookreview.com/assets/13336.jpg" width=360 border=0><BR>(<A target=_blank href="http://www.notebookreview.com/assets/13335.jpg" >view large image</A>)

    Constructed entirely of plastic, it has two fairly large fans in the center and rubber knob-things on the top to suspend your notebook off the surface. The overall build is quite durable and sturdy -- it won't flex if you try to bend it. It serves as a great platform to put a notebook on in your lap.

    Testing:

    Idle: 42 C CPU, 45 C HDD

    Under Load: 58 C CPU, 49 C HDD

    The Targus Chillmat did a pretty good job of cooling down my notebook. With the notebook in an idle state, the hard drive dropped a full four degrees. The hard drive is located at the front of my notebook, so it is hard to cool down. The idle state CPU saw a drop in temperature as well. Normally at 46 C at idle, I saw a 4 C drop to 42 C using the Chillmat. The area around the vicinity of the CPU stayed noticeably cooler.

    <IMG height=280 src="http://www.notebookreview.com/assets/13334.jpg" width=360 border=0><BR>(<A target=_blank href="http://www.notebookreview.com/assets/13333.jpg" >view large image</A>)

    One aspect of the Chillmat that I thought could be improved is the efficiency. The fans on the Chillmat are designed to draw air from the underside of the notebook and thrust it out the back. It would be better if the designers had focused on drawing heat from the back of the notebook and helping carry it away. It seems to me, just a higher velocity airflow across the bottom surface of the notebook would be more beneficial than a slow draw downward. The notebook gets cooler because of the air pushed upward by the fans, not the air pulled in.

    I'd recommend the Targus Chillmat to those wanting a simple, quiet cooling solution that is easy to transport. It works well, especially for those who like to put their notebook on their lap.

    Pros: Quiet, durable, and easy to transport. USB powered. Simple design.

    Cons: Cooling could be more efficient.

    <U>Spire Pacific Breeze</U>

    The Spire Pacific Breeze cooler is a rectangular, blocky unit with two case fans (essentially) embedded in either end, which take in air from above and thrust it out the bottom. The case fans have bright blue LEDs embedded in them -- you like them or you don't. It's not very portable, but it is durable. Power is provided by a USB port.

    <IMG height=156 src="http://www.notebookreview.com/assets/13338.jpg" width=360 border=0><BR>(<A target=_blank href="http://www.notebookreview.com/assets/13337.jpg" >view large image</A>)

    The Pacific Breeze did an excellent job of keeping my notebook cool, but with some compromises. Take a look at the tests first:

    Testing:

    Idle: 37 C CPU, 42 C HDD

    Load: 56 C CPU, 44 C HDD

    Air comes out of the Pacific Breeze very fast, and in great volume. This could even qualify as a desk fan. The combination of a lot of air moving quickly across the bottom of my notebook does wonders for heat reduction. My CPU temperature is exceptionally low, and the hard drive is well below the standard temp. The functionality of the cooler is great, but the practicality isn't. It's loud -- very loud. There are two settings for the fan speed, low and high. On low, the noise is very audible, and can be disruptive depending on the environment you're in. It basically sounds like a low-powered hair dryer. Forget about going to sleep with this in your room. On high, the sound increases considerably, I'd estimate by about one-third. Think of this as a hair dryer on medium. The sound is also more high-pitched...the low speed sounds like a growl.

    <IMG height=205 src="http://www.notebookreview.com/assets/13342.jpg" width=360 border=0><BR>(<A target=_blank href="http://www.notebookreview.com/assets/13341.jpg" >view large image</A>)

    My second point can be a compromise, depending on what kind of person you are. If you like LED lights and like to have a cool-looking setup, they're great. If you don't care about looks, well, the lights can be annoying. They cast a faded, cool blue light all around the area of your notebook. Decide for yourself whether you like them or not.

    Pros: Does an exceptional cooling job. Cheap and simple. USB powered.

    Cons: Very loud. Blue LEDs can be annoying.

    Number Three: Undervolting

    Cost: $0

    Time: 10-15 min (install, set voltage), 1.5-2.5 hours to test

    Difficulty: Moderate-Hard

    Applies to: Technical/More Advanced users

    This is not a step everyone can use -- my guide only applies to an Intel Pentium M (Sonoma) processor.

    Undervolting is a no-cost way of cutting down heat and power consumption in your notebook by reducing the amount of CPU voltage. It also increases battery life.

    You will need a program to undervolt -- I will be using <A target=_blank href="http://www.pbus-167.com/chc.htm" >Notebook Hardware Control (NHC)</A> for my Intel Pentium M 750 (1.86GHz) CPU.

    Once installed, run NHC and go to the CPU Voltage tab. Here you will see the multipliers on the left, and the voltage for that multiplier on the right. What needs to be changed is the voltage. Make sure all your other running programs are closed, and that you won't need to use the notebook for a couple hours -- the new voltages you set must be tested for stability.

    Most people can take down the voltage by .200V; my notebook has been stable for months. I don't guarantee that yours will be able to do the same, all are different.

    Set each of the multipliers down by .200V. After you set each multiplier, hit "Set" to do a short stability test. You'll need to restart your computer if for some reason it freezes up. Each short test takes thirty seconds. Once you have set all the multipliers, I recommend doing the full stability test.

    <IMG height=297 src="http://www.notebookreview.com/assets/13344.jpg" width=360 border=0><BR>(<A target=_blank href="http://www.notebookreview.com/assets/13343.jpg" >view large image</A>)

    Depending on how high or low-clocked your Pentium M is, it can take between three and four hours to do a full test. If done correctly and successfully, undervolting can take off several degrees from your CPU, and add a noticeable amount of battery life. My Pentium M 1.86GHz, without undervolting and not on a cooling pad, normally runs at 52 C. When undervolted, I lost six degrees, and am now running at 46 C. Not only Pentium Ms can be undervolted; look into whether or not your processor can.

    Step Four: Arctic Silver 5

    Cost: $7-$30

    Time: 20-40 minutes to apply

    Difficulty: Hard

    Applies to: Advanced users

    Arctic Silver 5 (AS5) is a thermal compound made of 99.9&#37; pure silver. It can take off up to ten degrees from your CPU, which is substantial. Keep in mind that this isn't the easiest option, but can yield excellent results if done right.

    Before you buy AS5, make sure you can get direct access to your CPU. If you cannot, then this step is not possible.

    <IMG height=288 src="http://www.notebookreview.com/assets/13348.jpg" width=200 border=0><BR>(<A target=_blank href="http://www.notebookreview.com/assets/13347.jpg" >view large image</A>)

    A view of my notebook's CPU with the heatsink removed.

    Turn off your notebook, unplug it, and remove the battery and bottom compartments to access the CPU. You may need to remove the heatsink or fan assemblies above the CPU. The rest of the procedure can be found on Arctic Silver's website in thorough detail, more than I could type up for you here. <A target=_blank href="http://www.arcticsilver.com/arctic_silver_instructions.html" >Link to procedure.</A>

    After allowing the Arctic Silver 5 thermal compound to set for the recommended 200 hours, I have seen a 3 C drop in temperature -- it gets better over time. Up to seven degrees can be taken off.

    I also noticed a difference in the amount of heat put off at full throttle. My notebook's fans do not come on nearly as often as they used to because the peak temperature is lower by 2 C.

    Conclusion

    After cleaning out the fans, getting a cooling pad, undervolting the processor and applying Arctic Silver 5 thermal compound, the results have been more than impressive for my notebook. Originally, I had a 46 C CPU temperature at idle, and the hard drive 49 C. After doing all of the above, my temperatures are down to 36 C CPU, and 42 C HDD. That's a 26.5% drop in the CPU, and a 14.3% loss in hard drive temperature. Hopefully, you will be able to achieve some of the same results I did. The time and effort are well worth it if you have a hot notebook, or even a modestly warm one. At most, you're looking at spending around $50 if you opt for the more expensive Targus ChillMat; I spent a total of $31 for canned air, a Pacific Breeze cooler, and a small tube of thermal compound.

    Anyone up for a weekend project?

     
    Last edited by a moderator: Jan 29, 2015 at 10:22 PM
  2. Fred from NYC

    Fred from NYC Notebook Evangelist

    Reputations:
    64
    Messages:
    501
    Likes Received:
    0
    Trophy Points:
    30
    Charles, thank you for this guide. It is nice to see a variety of options listed - and tested! - in one article.

    I would like to offer two observations. First, the CPU temperature under load increased by 1 degree with the Targus Chillmat. One could argue that this does not count as a "pretty good job" of cooling one's notebook because the hottest component in the notebook, the CPU, gets hotter with the Chillmat than without.

    Second, you write that the recommended set time for the Arctic Silver 5 thermal compound is 200 hours. Does this mean you cannot use the notebook for more than a week after you apply the compound?
     
  3. jwcornish

    jwcornish Newbie

    Reputations:
    2
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    5
    Regarding using compressed air to clear out dust.

    Please be aware that you can destroy the tiny brushless motors used by your notebooks fan by blowing canned air on them. If the fan is accessable, it would be a wise caution to 1) make sure your laptop is powered off, 2) use a straw or some other non conductive/sturdy device to hold the fan in place, and 3) then use the compressed air.
     
  4. deedeeman

    deedeeman Notebook Deity

    Reputations:
    406
    Messages:
    1,128
    Likes Received:
    3
    Trophy Points:
    56
    Verygood guide Chazman (charles)!!! this should be a sticky in the dummy section!!!

    i'll try some of the suggestions you posted....i hope it keeps my NB temperature low ;)
     
  5. jetstar

    jetstar Notebook Deity

    Reputations:
    1,095
    Messages:
    7,036
    Likes Received:
    0
    Trophy Points:
    205
    Excellent guide Chaz! Very comprehensive and informative! Thank you.
     
  6. Charles P. Jefferies

    Charles P. Jefferies TG Lead Moderator Super Moderator

    Reputations:
    13,736
    Messages:
    34,722
    Likes Received:
    464
    Trophy Points:
    501
    All the 'under load' temperatures are going to be near the same - the cooling pad doesn't do a ton for the CPU under load. Why it was one degree higher there, I'm not exactly sure but it isn't worth worrying about. ;)

    I've never heard this before, nor heard of any problems being caused because of it. I did say to make sure the laptop was powered off btw.
     
  7. Charles P. Jefferies

    Charles P. Jefferies TG Lead Moderator Super Moderator

    Reputations:
    13,736
    Messages:
    34,722
    Likes Received:
    464
    Trophy Points:
    501
    You can use it, it's just that for the compound to completely set, it takes 200 hours.
     
  8. Reize

    Reize Notebook Virtuoso

    Reputations:
    347
    Messages:
    2,652
    Likes Received:
    0
    Trophy Points:
    55
    Very nice guide Chaz, I'm sure it'll help a lot of people.

    I agree that a copy of this could be put in the dummy forum as a sticky and do very well.
     
  9. Jason

    Jason Overclocker NBR Reviewer

    Reputations:
    906
    Messages:
    5,053
    Likes Received:
    0
    Trophy Points:
    205
    Nice guide... I have some free time, and might try to make my own cooling pad ;) I recently opened up my desktop and noticed a ton of dust in the heatsink. I took an old toothbrush (didn't have canned air) and got all the dust out of the heatsink. My CPU now runs 4*C cooler. Another good way to cool off your lappy is to turn on the AC on full blast. :p
     
  10. E1505Guy

    E1505Guy Notebook Consultant

    Reputations:
    3
    Messages:
    148
    Likes Received:
    0
    Trophy Points:
    30
    Excellent guide. I'll try some of this stuff on my perpetually hot Dell XPS M140.
     
  11. Tim

    Tim Notebook Virtuoso

    Reputations:
    2,752
    Messages:
    3,142
    Likes Received:
    1
    Trophy Points:
    106
    Great guide Chaz. I blew out some dust just this last weekend. I should try to undervolt. :p
    Tim
     
  12. sony2k3

    sony2k3 Newbie

    Reputations:
    0
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    5
    There is a slight flaw with undervolting however. Since you are keeping the main chip cooler with less voltage on the clock, the fans won't run as often because chip temperatures never reach the fan turn on temp (unless you are able to change that as well, such as in Dells).

    Not letting the fan run actually causes heat build up elsewhere on your laptop where there are no temperature sensors because the heat has to go somewhere after being emitted from the chip. For my HP laptop, this location turns out to be the areas under the keyboard. I noticed that it got much hotter than usual after prolonged use and undervolting.

    Just something you guys might want to know.
     
  13. Metamorphical

    Metamorphical The Random Mod Super Moderator

    Reputations:
    2,613
    Messages:
    2,171
    Likes Received:
    2
    Trophy Points:
    56
    Lol, Where were you last summer Chaz? =) I could of used this guide then. But glad its here now.

    Target rocks! I got a two pack of compressed air cans (Fellows brand. Does it matter?) for $7. I also bought the Chillmat there a little while back. (Maybe it was a different one, but it looks the same... $25 on sale) I took it back. I just didn't see any difference in heat. Maybe I'll try another cooler later. I probably should be more motivated to get a another cooler for my notebook, but it's so much cooler than my old one I don't notice the heat so much, even with my notebook in my lap. Yet I know I'm hurting the air flow.
     
  14. emmzee

    emmzee Notebook Guru NBR Reviewer

    Reputations:
    7
    Messages:
    70
    Likes Received:
    0
    Trophy Points:
    15
    I got a Vantec Lapcool3 laptop cooler for my ASUS Z70V last year. It was about $25CDN I think. It cooled my hard drive 5 degrees or so, but did pretty much nothing for the CPU (maybe 1 degree, sometimes 0). The problem is that the fans (like the silver laptop cooler mentioned in this guide) are located in the middle; whereas the CPU on the Z70V is in the top right corner. So that one may help your HD but probably won't help your CPU (which is likely what you want to cool the most).
     
  15. ivar

    ivar Notebook Deity

    Reputations:
    432
    Messages:
    1,411
    Likes Received:
    0
    Trophy Points:
    55
    Good guide!

    Recently I found out that there is a better thermal paste than Arctic Silver 5!
    It is Coollaboratory LiquidPro based on liquid Indium and Gallium. It is suitable for cooper heatsinks only.
     
  16. Charles P. Jefferies

    Charles P. Jefferies TG Lead Moderator Super Moderator

    Reputations:
    13,736
    Messages:
    34,722
    Likes Received:
    464
    Trophy Points:
    501
    Interesting, I hadn't heard that before. I don't have any of those issues with my notebook; undervolting works best in conjunction with a cooling pad.

    My notebook has copper heatsinks all around, I'll have to look into it when it's time to replace the application I have on there now.

    That is a great deal, I believe I got ripped off at Best Buy ($7/can) :p The brand doesn't matter as far as I know.
     
  17. Metamorphical

    Metamorphical The Random Mod Super Moderator

    Reputations:
    2,613
    Messages:
    2,171
    Likes Received:
    2
    Trophy Points:
    56
    They have four packs there two. Can't remember how much they cost though. =P
     
  18. titaniummd

    titaniummd Notebook Deity

    Reputations:
    70
    Messages:
    1,746
    Likes Received:
    0
    Trophy Points:
    55
    Great guide, Chaz!

    How much battery life is lost using a cooling pad?
     
  19. 4W4K3

    4W4K3 Notebook Consultant

    Reputations:
    2
    Messages:
    130
    Likes Received:
    0
    Trophy Points:
    30
    Not sure if this has been addressed, but with some compressed air cans holding them upside down is hazardous. To test hold the can upside down and spray, you should get a very cold liquid compound to drip out of the nozzle. More than likely this is conductive, so it may ruin the laptop if you drip it in there.

    Just be sure to use the can right side up and you should be fine.
     
  20. Charles P. Jefferies

    Charles P. Jefferies TG Lead Moderator Super Moderator

    Reputations:
    13,736
    Messages:
    34,722
    Likes Received:
    464
    Trophy Points:
    501
    I do know that when you first use it, you need to get rid of the water by spraying it all out as I had posted in the guide. I never needed to turn it upside down, but that is worth considering. Thanks for commenting.
     
Similar Threads: Guide Cooling
Forum Title Date
Notebook Dummy Guide Articles [Guide] How to integrate video BIOS file into the motheboard's system BIOS based on Phoenix OR how to get romless video card work Aug 22, 2013
Notebook Dummy Guide Articles Installing mSATA ssd guide Nov 9, 2012
Notebook Dummy Guide Articles [Request] Guides for taking care of laptop Oct 22, 2012
Notebook Dummy Guide Articles Please Instruccions or Guide of: care, advice, recomendations, etc for my new clevo P170EM Jul 31, 2012
Notebook Dummy Guide Articles Guide: How to split/cut video files without loss of quality or re-encoding Mar 25, 2012

Share This Page