CLEVO P870TM1

Discussion in 'Sager and Clevo' started by luisxd, Jan 12, 2020.

  1. luisxd

    luisxd Notebook Consultant

    Reputations:
    21
    Messages:
    106
    Likes Received:
    26
    Trophy Points:
    41
    I don't know how good it is, screws are all the in, but i've noticed a slightly overheating (not always) while doing light stuff like moving files and installing things. I'll order some good thermal paste to see if that's the problem.
     
  2. joluke

    joluke Notebook Deity

    Reputations:
    592
    Messages:
    1,297
    Likes Received:
    703
    Trophy Points:
    131
    Sorry to say but that score seems to be a little off with the 8086k being at 5.1 and ATX off.

    Are you undervolting the cpu? something is crippling that cpu because the score is as close as mine and you are running at 5.1Ghz and i'm running at 4.7Ghz

    Here is the score i got with -0.125mV in my CPU and my gpu slightly overclocked (core: +165mHz and memory +525mHz with modified voltage curve):
     

    Attached Files:

  3. electrosoft

    electrosoft Tick Tock Clarice....

    Reputations:
    1,841
    Messages:
    2,897
    Likes Received:
    596
    Trophy Points:
    131
    If you have some cheap paste, do a pea size test and see how well it spreads after installing the heatsink.

    I found mine had a bad fit and progressively added shims till I had a near perfect spread and realized ~4.3mm was the optimal height.

    Moving files and installing things shouldn't be overheating the CPU.
     
  4. yrekabakery

    yrekabakery Notebook Virtuoso

    Reputations:
    900
    Messages:
    2,658
    Likes Received:
    2,526
    Trophy Points:
    181
    Heaven is almost entirely GPU-bound at those settings, so the CPU makes almost no difference. ;)
     
    joluke likes this.
  5. Papusan

    Papusan JOKEBOOKs Sucks! Dont waste your $$$ on FILTHY

    Reputations:
    26,517
    Messages:
    24,866
    Likes Received:
    44,031
    Trophy Points:
    931
    :)
    upload_2020-2-13_7-38-54.png
     
    luisxd and joluke like this.
  6. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,576
    Messages:
    53,475
    Likes Received:
    15,394
    Trophy Points:
    931
    The minimum can vary a lot, any slight hitch will change the value.
     
  7. jc_denton

    jc_denton V̖̟en̰g̻̼̰̩͙ea̲n̪c̭e̼ ͍̘̤͓̟̤Is̙͔ ̤Mi̻̭̣͎͍ͅn̰ḙ

    Reputations:
    3,127
    Messages:
    1,617
    Likes Received:
    2,185
    Trophy Points:
    181
    Rerun it, min should be around 30fps if it doesn't hiccup.
     
    joluke likes this.
  8. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    It runs 5.1Ghz day in and day out. It runs 5.1 is locked all the time. Unless I set windows to balanced power mode, then it would idle down when the machine is not under a load.
     
  9. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    My CPU is not crippled. Yes the cpu is undervolted -0.120V at 5.1Ghz with 4.8Ghz Cache frequency. It maybe hits 68-70C in this easy benchmark.

    My 5.1Ghz frequency reflects properly in everything else. R15, R20, or Firestrike.

    I think the test is just very GPU limited.

    If you really want to race CPU’s turn all of the settings on low and re run unigine haven. I will re run mine when I get home.
     
  10. tps3443

    tps3443 Notebook Deity

    Reputations:
    310
    Messages:
    1,099
    Likes Received:
    484
    Trophy Points:
    101
    Yea it’ll microstutter. I dunno why it does this. And it hurts the minimum fps.
     
Loading...

Share This Page