Clevo Overclocker's Lounge

Discussion in 'Sager/Clevo Reviews & Owners' Lounges' started by Spartan@HIDevolution, Mar 4, 2016.

  1. jc_denton

    jc_denton BGA? What a shame.

    Reputations:
    10,873
    Messages:
    3,034
    Likes Received:
    5,759
    Trophy Points:
    581
    I remember messing with CPU voltage on my p775tm1, had to switch from adaptive to override. But I forgot to set override voltage, so it was at "0".
    Safe to say it took me a while to figure out what I messed up, as fn+d didn't work and I had to do a full cmos reset. What a noob me.

    It removes all the cancer fitted into the firmware, that cripple you from behind the scenes. :)
     
  2. tps3443

    tps3443 Notebook Virtuoso

    Reputations:
    693
    Messages:
    2,165
    Likes Received:
    2,460
    Trophy Points:
    181

    FN+D+Power never worked for me. If I mess something up that results in black screen there’s gonna be a keyboard coming off lol. It wouldn’t be a bad idea to wire a CMOS button to the motherboard battery and run it underneath the bottom cover. And then you could just press the button and your good to go.
     
  3. tps3443

    tps3443 Notebook Virtuoso

    Reputations:
    693
    Messages:
    2,165
    Likes Received:
    2,460
    Trophy Points:
    181
    I can’t wait to get a P870TM1 chassis. How’s the CPU cooling on a P870 compared to my current P750? If I hit 85-92C at 5Ghz in AVX load on my 8086K, you think I could drop 10C?

    @jc_denton
     
    Last edited: Dec 28, 2019
  4. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    9,348
    Messages:
    57,892
    Likes Received:
    17,613
    Trophy Points:
    931
    There can be some options that could cause non boot too, even if prema has tried his best.
     
  5. Scerate

    Scerate Notebook Evangelist

    Reputations:
    224
    Messages:
    687
    Likes Received:
    650
    Trophy Points:
    106
    don't have any values but it should be quite a bit better due to vapor chamber cooling so basically the CPU shouldn't share the GPU temps + the CPU Heatsink is a bit beefier, so i dunno if 10 °C but couple of degrees for sure
     
  6. jc_denton

    jc_denton BGA? What a shame.

    Reputations:
    10,873
    Messages:
    3,034
    Likes Received:
    5,759
    Trophy Points:
    581
    When system is powered off, you press and hold fn+d then power on. You shouldn't hold down the power button.

    It should be a significant upgrade. TM1 CPU heatsink is much larger, has an additional 4th heatpipe, more rad space and larger fin area. As well as an extra rad for the VRM's.

    http://forum.notebookreview.com/thr...lounge-phoenix-4.809589/page-25#post-10639661

    But it all depends on Clevo heatsink lottery.. Some are slightly warped other are more crippled. Mine is warped and was hitting the ILM (retention bracket) and had very poor contact with the IHS when using LM.
     
  7. tps3443

    tps3443 Notebook Virtuoso

    Reputations:
    693
    Messages:
    2,165
    Likes Received:
    2,460
    Trophy Points:
    181
    So tell me, I was reading you signature. Your laptop RTX2080 is clocked very similar to your desktop RTX2080. How do they compare?
     
  8. tps3443

    tps3443 Notebook Virtuoso

    Reputations:
    693
    Messages:
    2,165
    Likes Received:
    2,460
    Trophy Points:
    181
    I ordered some K5 Pro (30 Grams), and a rockitcool copper IHS for my 8086K, I also ordered 5 Grams of Thermal Grizzly Conductonaut.

    I am hoping the K5 Pro does good for thermal pad replacement. I am going to use it every where.

    Id be surprised if this IHS could actually lower temps on my CPU. If it does, then that is great! But so far I am 100% good at 5Ghz without throttle. I’m after lower GPU temps for now though. So I’m Hoping the K5 Pro helps some.
     
    Last edited: Dec 29, 2019
    hmscott likes this.
  9. Falkentyne

    Falkentyne Notebook Prophet

    Reputations:
    8,384
    Messages:
    5,990
    Likes Received:
    8,629
    Trophy Points:
    681
    Why did you order 5 grams of conductonaut? How much was that? :(
    I see it as over $40 on amazon. Remember what I told you?

    For that price, you can get:

    https://www.amazon.com/gp/product/B0792TB9GX/

    2 of these: (40g to match the 100g above)
    https://www.ebay.com/itm/Indium-Met...510144?hash=item33f2d70600:g:xRQAAOSwze9c0MrH

    https://www.ebay.com/itm/Tin-Metal-...604222?hash=item56b5a3e3be:g:10cAAOSwWo5bfyfM

    Mix 50g of Gallium, 20 grams of Indium, 10 grams of Tin into a crucible, throw it in the oven, melt and mix it well, grab some assorted syringes and some nozzle needle-nose syringes (be careful of the straight metal thin tube versions, something like what is included with Conductonaut is much better (you can even use the conductonaut tip on the syringes!), and you get about 60 grams, with half the materials remaining for more (50g/20g/10g).
     
    Last edited: Dec 29, 2019
    tps3443 likes this.
  10. tps3443

    tps3443 Notebook Virtuoso

    Reputations:
    693
    Messages:
    2,165
    Likes Received:
    2,460
    Trophy Points:
    181
    You are right. I’m so stupid. I forgot all about mixing it myself. I use so much LM too. It really goes fast.

    With rubbing the LM in, letting it soak, applying more. Then if you take your heatsink off again to adjust a pad or something, it is all rinse and repeat and then your out lol.

    it was over $40 bucks. 5Ghz with 0 AVX requires frequent LM maintenance for optimal temps lol.
     
Loading...

Share This Page