Clevo Overclocker's Lounge

Discussion in 'Sager/Clevo Reviews & Owners' Lounges' started by Ultra Male, Mar 4, 2016.

  1. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,108
    Messages:
    51,285
    Likes Received:
    14,625
    Trophy Points:
    931
    Speak to EVOC about it, they may have a work around.
     
  2. senso

    senso Notebook Evangelist

    Reputations:
    241
    Messages:
    683
    Likes Received:
    157
    Trophy Points:
    76
    Do you have Intel XTU installed?
    It can do those kind of things..
     
  3. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    8,235
    Messages:
    6,093
    Likes Received:
    15,536
    Trophy Points:
    681
    Very nice! :)
    1500Mhz on vRAM is an outstanding sample...never seen one before.

    I left the heatpipes intact on my P870DM3 when upgrading to the TM1 CPU heatsink. But I just bend them over the CPU heatsink, so same as before just higher.
     
    jaybee83, Papusan and jc_denton like this.
  4. jc_denton

    jc_denton Notebook Evangelist

    Reputations:
    416
    Messages:
    424
    Likes Received:
    397
    Trophy Points:
    76
    Thanks bro Prema! :)

    Did you see temp improvements by doing so? I'd imagine that the VC would tank the heat from the CPU by doing so.
     
  5. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    8,235
    Messages:
    6,093
    Likes Received:
    15,536
    Trophy Points:
    681
    I don't have a comparison, as I have only ever used it that way, but I assume it offloads a bit of that 9900K heat:

    [​IMG]
     
  6. jc_denton

    jc_denton Notebook Evangelist

    Reputations:
    416
    Messages:
    424
    Likes Received:
    397
    Trophy Points:
    76
    Woah! That's absolutely nuts! :D Is that is non-ac run with tjmax offset? As that would be way better than adding in a 4th fan.

    Do you have any pictures of how you modded it or how it sits?
     
  7. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    8,235
    Messages:
    6,093
    Likes Received:
    15,536
    Trophy Points:
    681
    Na, already modded the heatsinks back when the P870TM1 was new and never made any pictures. But the bottom cover can no longer make the click-in or it would be too tight.

    That CB15 run is also ancient, usually just don't post that stuff. I didn't touch the thermal limits, but IIRC it would start to thermal throttle if CB15 would be a slightly longer bench. It runs 3DMark at 5.1Ghz (which has a lot lower CPU load) and is also very close to thermal throttle at the end of the combined load test (full FAN no AC).

    Wonder how Clevo intends to keep 10 cores cool in the smaller LGA 1200 chassey while a 200W~ GPU is active at the same time (at least they finally woke up on the TGP part). Maybe that larger FAN....
     
    Last edited: Sep 12, 2019 at 10:54 AM
  8. jc_denton

    jc_denton Notebook Evangelist

    Reputations:
    416
    Messages:
    424
    Likes Received:
    397
    Trophy Points:
    76
    That's definitely a successful mod, I would say. A unified VC mod. Comparing to my own experience, this does in fact soak quite a bit of heat when compared to stock TM1/9900k combo, even with an extra fan. 4.9G being the upper limit for CR15 for me.
     
    Last edited: Sep 12, 2019 at 11:16 AM
  9. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    8,108
    Messages:
    51,285
    Likes Received:
    14,625
    Trophy Points:
    931
    Fin area, airflow or more efficient heat transportation are your only options.
     
    joluke likes this.
  10. Papusan

    Papusan JOKEBOOK's Sucks! Dont waste your $$$ on FILTHY

    Reputations:
    21,960
    Messages:
    23,274
    Likes Received:
    40,265
    Trophy Points:
    931
    The cooling design is still 340W. The only savior is a revision 2 HS with higher thermal capacity. This if the cooling we have seen is correct from the leak.
     
    Falkentyne likes this.
Loading...

Share This Page