Clevo Overclocker's Lounge

Discussion in 'Sager/Clevo Reviews & Owners' Lounges' started by Ultra Male, Mar 4, 2016.

  1. Johnksss

    Johnksss Notebook Nobel Laureate

    Reputations:
    9,687
    Messages:
    18,239
    Likes Received:
    8,769
    Trophy Points:
    931
    If it's the P870DM3, you might be able to get away with an inline flash...If it's the actual TM1 then yes, you will need to remove the chip from the board
     
    Ashtrix, Prema, Papusan and 1 other person like this.
  2. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    7,520
    Messages:
    47,205
    Likes Received:
    12,743
    Trophy Points:
    931
    It is a dm3 chassis, I'll have a play later with it.
     
    Papusan, Johnksss and Prema like this.
  3. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    7,402
    Messages:
    5,739
    Likes Received:
    13,583
    Trophy Points:
    681
    Yeah, we had a little communication gap between two mails and some rather important info reached him too late...my bad
     
    Last edited: May 16, 2018
  4. Johnksss

    Johnksss Notebook Nobel Laureate

    Reputations:
    9,687
    Messages:
    18,239
    Likes Received:
    8,769
    Trophy Points:
    931
    I'm already knowing. At least it wasn't like me..... The waiting (3 hours on a reply...maybe. lol) was killing me so I would start experimenting. lol
     
    Papusan and Prema like this.
  5. Georgel

    Georgel Notebook Virtuoso

    Reputations:
    844
    Messages:
    2,371
    Likes Received:
    2,740
    Trophy Points:
    181
    I've been using one EK Vardar for a while now, it can cool a 8700K on a water loop to 4.8GHz and full time work, I think it will be enough for most people and it is the best I've tried. Noisy af when at max, but it pushes more air at lower RPM than other fans, by your graph, so it ends up being quieter in the long run, if this makes sense
     
    Papusan likes this.
  6. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    7,520
    Messages:
    47,205
    Likes Received:
    12,743
    Trophy Points:
    931
    You don't jump in early without knowing there are risks and accepting the consequences that can go with them.
     
    Vasudev, Papusan, Prema and 1 other person like this.
  7. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    7,402
    Messages:
    5,739
    Likes Received:
    13,583
    Trophy Points:
    681
    Bricked (& recovered) my own system today. Turns out that a disabled ME is really unpredictable when being re-enabled...shut the system right down while still flashing.
    Thank God I socketed the BIOS chip right when installing the KM board.
     
    DreDre, Vasudev, jclausius and 4 others like this.
  8. bloodhawk

    bloodhawk Derailer of threads.

    Reputations:
    2,907
    Messages:
    5,846
    Likes Received:
    8,535
    Trophy Points:
    681
    Did you pull lines over to an accessible area or just added a socket at the usual place?
     
  9. Prema

    Prema Your Freedom, Your Choice

    Reputations:
    7,402
    Messages:
    5,739
    Likes Received:
    13,583
    Trophy Points:
    681
    No, just put a socket in place.

    Usually I don't brick things anymore these days (the entire Coffee Lake compatibility development went without a single one), so it was more the habit of installing it than expecting to actually need it.

    Bricked those two systems, dropped my AC Adapter from 10 feet, burned my U11's charging port...guess I am having one of those weeks where I should just have gone hiking instead of touching tech. :oops:
     
    Last edited: May 16, 2018
    DreDre, D2 Ultima, Legion343 and 7 others like this.
  10. Meaker@Sager

    Meaker@Sager Company Representative

    Reputations:
    7,520
    Messages:
    47,205
    Likes Received:
    12,743
    Trophy Points:
    931
    You can get sockets that match the normal pads.
     
    Papusan and Prema like this.
Loading...

Share This Page