Acer Aspire TimelineX 3820TG mods/tweaks ONLY!

Discussion in 'Acer' started by prikolchik, Mar 16, 2011.

Thread Status:
Not open for further replies.
  1. _InKr_

    _InKr_ Notebook Guru

    Reputations:
    11
    Messages:
    72
    Likes Received:
    0
    Trophy Points:
    15
    Here it is
     

    Attached Files:

  2. inteks

    inteks Notebook Evangelist

    Reputations:
    168
    Messages:
    372
    Likes Received:
    0
    Trophy Points:
    30
    nize . thank you ! :)
     
  3. inteks

    inteks Notebook Evangelist

    Reputations:
    168
    Messages:
    372
    Likes Received:
    0
    Trophy Points:
    30
    i found a small problem. the cpuFan dont get to 100% even at 95°C is it also with org kbc file ?

    is it possible to force 100% above 95°C via kbc mod?
     
  4. prikolchik

    prikolchik Notebook Evangelist

    Reputations:
    259
    Messages:
    362
    Likes Received:
    2
    Trophy Points:
    30
    What do you mean by "100%"? Even if you set fan speed to 0x00 in RWEverything, the fan will only go up to 0x6F, which seems to be the maximum possible speed.
     
  5. inteks

    inteks Notebook Evangelist

    Reputations:
    168
    Messages:
    372
    Likes Received:
    0
    Trophy Points:
    30
    but with the latest KBC it dont raise up to 100% - 0x6F - 0x00 ....
    i set TDP/TDC from 25 to 50 and start prime to use all 4 cores to see if turboboost stays @ 21x multiplier and yepp it does ;)
    BUT after a few miuntes temp of CPU raise up to 96°C and i thought the fan is to silent . then i start cpufan control in 3820tray and the fan speed up twice as fast as before :eek:
     
  6. _InKr_

    _InKr_ Notebook Guru

    Reputations:
    11
    Messages:
    72
    Likes Received:
    0
    Trophy Points:
    15
    I'll check this.
     
  7. _InKr_

    _InKr_ Notebook Guru

    Reputations:
    11
    Messages:
    72
    Likes Received:
    0
    Trophy Points:
    15
    Hm. In KBC max CPU Fan speed is set to 0x6F, but if setting 0x0 in RWEverything - resulting speed is 0x60 which is noticeably (not twice of course ;) ) louder/faster than 0x6F. I'm not sure why Acer's engineers did such thing, but probably they had reasons for it.
     
  8. inteks

    inteks Notebook Evangelist

    Reputations:
    168
    Messages:
    372
    Likes Received:
    0
    Trophy Points:
    30
    is it possible to change it ? can you set it to 100% (0x60) if temp is above 90C°
    or is it also louder at i.e 70°C then ?
     
  9. _InKr_

    _InKr_ Notebook Guru

    Reputations:
    11
    Messages:
    72
    Likes Received:
    0
    Trophy Points:
    15
    This can be done for >85C°. But actually, I still have some doubts regarding this: what if there are issues with fan on this speed? Will you take this risk?
     
  10. inteks

    inteks Notebook Evangelist

    Reputations:
    168
    Messages:
    372
    Likes Received:
    0
    Trophy Points:
    30
    hmmm... i dont know. what is the worst case? damaged fan ? burned mainboard (fan sucks to much power at this speed...) :rolleyes:

    the engineers leave some room for overclocked and KBC modded rig :D

    Seriously i dont think a fan takes damage when running on 100% (designed for) speed
     
Loading...
Thread Status:
Not open for further replies.

Share This Page