2102: detection error on HDD1 (ultrabay HDD)

Discussion in 'Lenovo' started by fraushai, Jun 20, 2011.

Thread Status:
Not open for further replies.
  1. fraushai

    fraushai Notebook Evangelist

    Reputations:
    14
    Messages:
    307
    Likes Received:
    0
    Trophy Points:
    30
    I just got my X220i today which had a 250gb 5400rpm hard disk. Everytime I boot up this message popped up followed by 'Press Esc to continue'.

    When I pressed Esc, however, I was able to boot up and use my computer normally.

    Also, I was unable to access bios when I pressed F1/2 during boot.

    Can anyone help me out on that?

    Thanks!
     
    fraushai, Jun 20, 2011
    #1
  2. ZaZ

    ZaZ Super Model Super Moderator

    Reputations:
    4,870
    Messages:
    33,732
    Likes Received:
    1,106
    Trophy Points:
    581
    Sure that wasn't 2010?
     
    ZaZ, Jun 21, 2011
    #2
  3. fraushai

    fraushai Notebook Evangelist

    Reputations:
    14
    Messages:
    307
    Likes Received:
    0
    Trophy Points:
    30
    yes 10char
     
    fraushai, Jun 21, 2011
    #3
  4. ZaZ

    ZaZ Super Model Super Moderator

    Reputations:
    4,870
    Messages:
    33,732
    Likes Received:
    1,106
    Trophy Points:
    581
    2010 usually means your drive is going. I'd run the Lenovo diagnostic on it and if it fails, have Lenovo replace it. Good Luck.
     
    ZaZ, Jun 21, 2011
    #4
  5. fraushai

    fraushai Notebook Evangelist

    Reputations:
    14
    Messages:
    307
    Likes Received:
    0
    Trophy Points:
    30
    sorry, i meant that it was 2102 NOT 2010.
     
    fraushai, Jun 21, 2011
    #5
  6. fraushai

    fraushai Notebook Evangelist

    Reputations:
    14
    Messages:
    307
    Likes Received:
    0
    Trophy Points:
    30
    following the instructions in the x220 hardware maintenance menu, i took out the hard disk and then put it back immediately. however, the error 2102 still persisted.

    Can someone help?
     
    fraushai, Jun 21, 2011
    #6
  7. fraushai

    fraushai Notebook Evangelist

    Reputations:
    14
    Messages:
    307
    Likes Received:
    0
    Trophy Points:
    30
    help please? should i send the unit back to lenovo?
     
    fraushai, Jun 21, 2011
    #7
  8. ZaZ

    ZaZ Super Model Super Moderator

    Reputations:
    4,870
    Messages:
    33,732
    Likes Received:
    1,106
    Trophy Points:
    581
    Why don't you call Lenovo and see what they have to say. I'm not familiar the 2102 error code.

    P.S. - No bumps for 24 hours, per the forum rules.
     
    ZaZ, Jun 22, 2011
    #8
  9. jesuisfil

    jesuisfil Newbie

    Reputations:
    0
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    5
    I met the same problem as yours a few days ago.
    A simple method to resolve it is to diagnose your computer system with Lenovo ThinkVantage Toolbox.If the resilt is normal,reboot computer.
    _________________________________________________________
    the same problem appears again!!!
     
    jesuisfil, Jul 28, 2011
    #9
  10. jesuisfil

    jesuisfil Newbie

    Reputations:
    0
    Messages:
    7
    Likes Received:
    0
    Trophy Points:
    5
    To access the BIOS for X220i ,press F1 during startup when the ThinkPad logo is displayed.
     
    jesuisfil, Jul 28, 2011
    #10
Thread Status:
Not open for further replies.

Share This Page