1.8" SATA Drive Enclosure Recommendataions? | Page 2 | NotebookReview

1.8" SATA Drive Enclosure Recommendataions?

Discussion in 'Lenovo' started by pem69, Sep 3, 2009.

Thread Status:
Not open for further replies.
  1. dawn

    dawn Notebook Consultant

    Reputations:
    9
    Messages:
    114
    Likes Received:
    0
    Trophy Points:
    30
    I didn't mean to offend nor accuse you and I'm sorry you have understood my post in that way. I have never questioned that the setup you were describing might work under some circumstances, rather I was questioning your generalisation that it always works. All I wanted was to draw attention of those intending to run such a setup to the potential problems that might be involved. Hence the thread I was referring to.

    I don't have time nor will to do any extensive testing on this subject, even more so because it's of no particular interest to me. Still I believe that standard third-party USB-powered enclosures would not supply 3.3V, because it would require additional circuitry (=extra cost) when all that is needed to power 2.5" notebook HDD is 5V (which is provided conveniently by USB). Yes, I have seen USB enclosures, which were more expensive and specifically claimed to have voltage conversion for 1.8" drives and these would certainly work.

    I have no means to test it because I don't own one (you have so you can give it a try) but based on what other users wrote in the Lenovo forums, 1.8"-2.5" storage converters from Lenovo (42W7888 / 42W8019) don't have any on-board voltage conversion.
    See here: Re: Micro SATA SSD using external adapter - not powering up
     
    Last edited by a moderator: May 8, 2015
  2. erik

    erik modifier

    Reputations:
    3,647
    Messages:
    1,610
    Likes Received:
    0
    Trophy Points:
    55
    these users are correct in saying that neither of the storage adapters have any conversion circuitry.   all they do is route the power and data pins from the SATA socket to the corresponding pins on the micro-SATA socket.   if a USB caddy does not supply power to the +3.3V pins for some reason (which breaks SATA specifications) then of course a 1.8" drive will not work.   what i said above does not apply to improperly-designed storage caddies.

    my personal experience with two USB-based solutions has been positive thanks to using properly-designed hardware. ;)
     
  3. pem69

    pem69 Notebook Consultant

    Reputations:
    22
    Messages:
    216
    Likes Received:
    0
    Trophy Points:
    30
    Back on topic, anyone know of good enclosures?
    The (potential) best I've found is one like this:
    http://cgi.ebay.com/1-8-SATA-to-USB...rnal?hash=item439a017aef&_trksid=p3286.c0.m14

    But I can't quite tell, and I'm waiting to hear back about some specs.

    I'm continually amazed when I see enclosures like this:
    http://cgi.ebay.com/USB-2-0-PORTABL...rnal?hash=item45ede80b88&_trksid=p3286.c0.m14
    Most specifically:
    Dimensions 2.8"x3.2"x0.4"
    Hardly a 1.8" enclosure, now is it! (Nor is the interface type clear).

    Suggestions still greatly appreciated.

    Thanks.


    Edit: I'll also post this one, in case anyone else is interested: http://cgi.ebay.com/SATA-IDE-USB-1-...ries?hash=item19b63d5646&_trksid=p3286.c0.m14
    A very nice (and relatively inexpensive) external multi-interface/size device.
     
  4. erik

    erik modifier

    Reputations:
    3,647
    Messages:
    1,610
    Likes Received:
    0
    Trophy Points:
    55
    if size is your biggest concern, have you considered buying a small external drive like the trekstor microdisk?   it's only 3.3" x 2.2" x 0.3".

    http://www.amazon.com/gp/product/B001EMRNE4/

    i've been searching for dedicated 1.8" micro-SATA enclosures for over a year and have yet to find one.   everything i've seen uses a 2.5" drive enclosure with an adapter of some sort.
     
  5. pem69

    pem69 Notebook Consultant

    Reputations:
    22
    Messages:
    216
    Likes Received:
    0
    Trophy Points:
    30
    Oooh, shiny! Size is a little bit of a concern, but at the same time I do want to use the extra drive I'll have (1.8" replaced with an SSD), which is why I was looking for an enclosure. I just figured "why have a larger enclosure for a tiny drive"? Or do you think it would just be better to sell the drive on Ebay, and get something else as a replacement? The 120->250 (HDD) isn't a whole lot and it seems rare enough online that it might be worth a premium - I didn't find the bigger one listed anywhere.
     
  6. pem69

    pem69 Notebook Consultant

    Reputations:
    22
    Messages:
    216
    Likes Received:
    0
    Trophy Points:
    30
    So I head back from the seller of that first item. He says it's a 1.8" drive enclosure (78mmx88mm, outside), but that it's standard SATA instead of micro SATA, and there's no room for a connector. I was confused, and then remembered I'd seen some drives with the SATA connector on the long side, instead of the short side. I guess that's the difference - the older style drive.

    Back to searching, unless someone thinks it'd be a better idea just to sell it.
     
  7. dannytom

    dannytom Newbie

    Reputations:
    0
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    5
    I saw your post and I thought I should share with you where I found an enclosure for my Micro SATA Drive 3.3V. This link is http://www.microsatacables.com/catalog/c60_p1.html they have a lot of options for enclosure cases that use an adapter for 3.3V that you plug into the case.

    The case worked great.
     
  8. pem69

    pem69 Notebook Consultant

    Reputations:
    22
    Messages:
    216
    Likes Received:
    0
    Trophy Points:
    30
    Good to hear they have some positide review. I'd seen them and had been tempted, though I'd thought they were priced a bit high. But the extra knowledge that they're reliable might be worth it.
     
  9. dannytom

    dannytom Newbie

    Reputations:
    0
    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    5
    Very helpful, worth every penny
    :)
     
  10. pem69

    pem69 Notebook Consultant

    Reputations:
    22
    Messages:
    216
    Likes Received:
    0
    Trophy Points:
    30
    One more follow up question, here. Did this drive require a USB-Y adaptor (to steal extra power)? Do most 2.5" drive enclosures need this? I ask because I was about to buy this one, and noticed that there are a ton of 2.5" enclosures for far cheaper than the $40 shipped, and I could buy the sata-to-microsata converter for about $10. However, I'd prefer not needing to use the extra USB port that most enclosures seem to. Or is this not possible?
    Why not, considering the spec is for 5V?
     
Loading...
Thread Status:
Not open for further replies.

Share This Page