*HP 2510p Owners Lounge*

[Mike60]

I`ve forgotten place a picture with Intel WiFi 6200AGN.
It is not so nice processed but it`s work

[handshake987]

Hi Guys,
I'm new here, but I already have a question.
I use Ubuntu 10.10 Maverick as the operating system, which works great.
Only with the track point I have massive problems. It is totally slow.

can someone give a tip here?

@ mike60 I have the same card installed .. The card works just great compared to the broadcom ...

[User Retired 2]

can someone give a tip here?

@ mike60 I have the same card installed .. The card works just great compared to the broadcom ...

Welcome aboard. I too had a slow touchstyk with a default Ubuntu installation which was corrected with:

xset mouse 25/10 2.5

Consider posting any other mods you may have if you wish to be included on the first post as an example. Appears you are using the modded_bios and 6200AGN.wifi.

[Ayori]

Hey guys I need help on installing the network interface drivers for BackTrack 4 R2 Kernel 2.6.35.8 (I thought this would have the drivers already). When I open the network interfaces it only shows the loopback interface and nothing else. Here are the network cards on my 2510p:
Broadcom 4321AG
Intel 82566MM

Thanks for your help!

[Mike60]

Trying to install Gobi-2000 on 2510p I have bad news.
But I don`t understand ?
Take out WWAN card the same.
Turn AMT in Bios Enable or Disable the same.
I must reinstall W7 ?

Mike

[Evilandi666]

I asked for autotrim - but I think this is not possible. (rr3636 did only manual trim testing). But no problem, Linux has a wipe.sh for that

But i don't know if i should use the ssd furthermore, because i have some strange problems with it: Sometimes my HP won't boot (stucks at Bios with both HDD Leds on but not going on.) and sometimes when I resume from Standby (stucks with both HDD LEDs on.).
Did anyone have this problems before? Is there a solution? I don't know if the problem is the Vertex2 or the Caddy ... mhh.

Or is this the famous 30 sec. bios hang? But ebay caddys are not affected normally.

After waiting 30 Seconds it says that the harddrive is not a system drive or something like that. After reboot it boots fine.. :/

Can someone tell me how the 30 Seconds hang does look like? Like I described my problem or does it have other behaviour?

I don't know if my caddy was broken or why this problem exists, but i ordered a newmodus caddy - i thought long time about it, because its very expensive compared to the chinese caddys. (about 60 $ for me incl. shipping for newmodus, 25 $ incl. for chinese.)

Don't know yet if this desicision is good, but will report back when fedex delivers it to me.

Also there is a 5% Coupon for newmodeus: FB072808 (Found it here)

[chris32303]

Nando4 or anyone else:

Can you post details or screenshots on what settings I should set my 2510P to in Throttlestop and Setfsb for overclocking? My processor is the U7600 1.2 dual core and I am using the latest F.O.F modded bios. Without using Throttlestop, I have been able to overclock in to 1.4 GHZ in setfsb by moving to top slider to 271 and the bottom one to 409 BUT I would like to go go to 1.5 or 1.6 GHZ.
What settings do I need to use in Throttlestop so that I can overclock it to a higher setting? Also, after configuring Throttlestop what settings do I use in Setfsb?

Thanks in advance for anyone who can help me with this.

[User Retired 2]

Nando4 or anyone else:

Can you post details or screenshots on what settings I should set my 2510P to in Throttlestop and Setfsb for overclocking? My processor is the U7600 1.2 dual core and I am using the latest F.O.F modded bios. Without using Throttlestop, I have been able to overclock in to 1.4 GHZ in setfsb by moving to top slider to 271 and the bottom one to 409 BUT I would like to go go to 1.5 or 1.6 GHZ.
What settings do I need to use in Throttlestop so that I can overclock it to a higher setting? Also, after configuring Throttlestop what settings do I use in Setfsb?

Refreshed the 2510P Performance Toolkit 1a which you are welcome to try. It does most of the hard integration work for you. The default parameter for my U7600 being 160x10@0.9125V (AC, dualIDA) and 160x9@0.85V (DC). The DC overclock being the highest stable point at the lowest voltage which provides battery life improvements.

It should take 5 mins to install, setup and enjoy It automatically activates after a resume-from-standby/hibernate as well.

[chris32303]

Nando4,

Unfortunately that performance toolkit is not working for me. I followed the instructions exactly like it says and as soon as I boot into windows 7 I get a popup message that says "You are about to be logged off" "Windows will shut down in 1 minute"
While that is happening I get (2) separate popup windows wanting me to grant access to setfsb and Throttlestop which I click "yes" on both on them. Also, at the same time in my taskbar I can see where the batch file is running from where I placed a shortcut in my startup folder. However, Windows shuts down on me after that 1 minute.
In my power options I am using the High Performance option. I've also tried this using balanced but it still shuts down within 1 minute. Lastly, it doesn't make a difference if I am running on AC or DC power because either way Windows shuts down within the 1 minute.

Here are my specs again in case you need them.

HP 2510P with a Intel U7600 Dual Core 1.2 GHZ
2GB stock memory
F.OF (267) modded bios
(factory/stock) 120GB Toshiba MK1214GAH hard drive
Windows 7 Ultimate

Can you PLEASE help? I am really wanting to overclock this laptop. Thanks

[User Retired 2]

Unfortunately that performance toolkit is not working for me. I followed the instructions exactly like it says and as soon as I boot into windows 7 I get a popup message that says "You are about to be logged off" "Windows will shut down in 1 minute"
..
Can you PLEASE help? I am really wanting to overclock this laptop. Thanks

Updated to 2510P Performance Kit 1.0b with a new step to manually install BarEdit to correct the problems you've highlighted.