How to pinmod and further overclock the M11x R1 (SLG= Hardmod only)

[bavman]

dang, well if it can only be set at boot then unless you can find a way to mod the bios i dont think anything else will work out.

[some guy]

just looked around again and figured id post the only 2 sets i found that might work for us here?

Newegg.com - Kingston HyperX 4GB (2 x 2GB) 204-Pin DDR3 SO-DIMM DDR3 1333 Laptop Memory Model KHX1333C7S3K2/4G

Newegg.com - Kingston HyperX 4GB (2 x 2GB) 204-Pin DDR3 SO-DIMM DDR3 1066 (PC3 8500) Laptop Memory Model KHX1066C5S3K2/4GX



good luck with figuring out that PLL DavyGT.

[DavyGT]

just looked around again and figured id post the only 2 sets i found that might work for us here?

Newegg.com - Kingston HyperX 4GB (2 x 2GB) 204-Pin DDR3 SO-DIMM DDR3 1333 Laptop Memory Model KHX1333C7S3K2/4G

Newegg.com - Kingston HyperX 4GB (2 x 2GB) 204-Pin DDR3 SO-DIMM DDR3 1066 (PC3 8500) Laptop Memory Model KHX1066C5S3K2/4GX



good luck with figuring out that PLL DavyGT.

I'll take this kit. It's cheaper and stable at a higher speed, at CAS6.

[DR650SE]

Yea, thats the kit I have that I showed in the screenshots. Once I get some nerve up, (worried I might cut the wrong pin) I'll try out some benching with it.

[DavyGT]

I've been comparing both PLLs and I swear, one company must have went "Ctrl+C, Ctrl+V". Both PLLs have the same pin configuration, just some with different names on the datasheets. I suspect TME is still PIN 14.

[some guy]

I'll take this kit. It's cheaper and stable at a higher speed, at CAS6.

thats what i was thinking... seeing as how DR650SE has the same kit and got his m11x to boot with it, i think its our best shot. plus the heat spreaders will help with the drop in timings to cas6

wondering if i should order my kit now so its here when my M11x arrives.

I've been comparing both PLLs and I swear, one company must have went "Ctrl+C, Ctrl+V". Both PLLs have the same pin configuration, just some with different names on the datasheets. I suspect TME is still PIN 14.

do you have both versions of the PLLs at your disposal over there or are both of your M11xs using the ICS PLL?

[DavyGT]

thats what i was thinking... seeing as how DR650SE has the same kit and got his m11x to boot with it, i think its our best shot. plus the heat spreaders will help with the drop in timings to cas6

wondering if i should order my kit now so its here when my M11x arrives.





do you have both versions of the PLLs at your disposal over there or are both of your M11xs using the ICS PLL?

I only got 1 M11x with an ICS PLL, that's why I had to repeat both mods.

I'm hoping the SLG is a clone of the ICS. Fairly sure PIN 14 (PCI2) is TME as Silego has a pattern of sharing PCI2 with TME in their PLLs.

[bavman]

I only got 1 M11x with an ICS PLL, that's why I had to repeat both mods.

I'm hoping the SLG is a clone of the ICS. Fairly sure PIN 14 (PCI2) is TME as Silego has a pattern of sharing PCI2 with TME in their PLLs.

You think they'd tell us if we ask?

[DavyGT]

You think they'd tell us if we ask?

They'll deny it and call it their own design. Can you ask for older and newer versions of the datasheet instead? The one I got has Preliminary under every page. We're looking for a datasheet that confirms TME is PIN 14, PCI2. Thank you for contacting Silego for the original datasheet.

[some guy]

you may have to give them more info about the application thats being used.

at least thats what the lady i emailed with told me. she said i would need to contact the manufacture of the product that the chip was used in to get more info.

logically i don't see why the PLLs would be any different in the way the pins are laid out. maybe internal differences but if the pin layout was any different it would call for a different motherboard revision. which just doesn't make sence to go thru all that engineering just for one different chip.

i think dell/alienware would more likely have a company produce something similar to the first chip to fit the exact physical/functioning specs.